Call (661) 252-1400

Go to…

RAM

Home / RAM

We Service and Repair all RAM cars

  • 2021 RAM ProMaster 1500

    RAM ProMaster 1500
    Mileage
    45,853
    Service Date
    9/28/2023
    Services Performed
    • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
     
    JEFF J. gave our service a 5 star review on 9/29/2023

  • 2012 RAM Pickup

    RAM Pickup
    Mileage
    198,945
    Service Date
    8/11/2023
    Services Performed
    • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
    • You vehicle's diagnostic system has detected a problem that is causing it not to perform to factory standards, resulting in the control module turning on the check engine light (CEL). We are well equipped & trained to accurately diagnose & repair these problems. We can & will repair the car to factory standards, however, there may be more than one problem present. The engine management computer of your car is equipped with a sophisticated on-board diagnostic (OBD) system. When this system detects a problem it turns on the CEL. A problem in one of the monitored system is what turned on your CEL. Our technicians are highly trained & equipped with the latest state of the art diagnostic equipment, so that in most cases we will be able to diagnose & repair problems quickly and efficiently. There may be more than one problem present even though only one trouble code was recorded in the module. The module continually runs various self tests to ensure that all systems are working normally. In the event of a failure some of these self tests are turned off until the original problem is fixed. This means that until we repair the original problem we may not be able to see other problems. This is likely to occur if you have been driving with the CEL for multiple days.
    • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
    • Replace rear brake pad linings and machine rear brake disc rotors on vehicle with new state of the art on car brake lathe, THAT WILL PERFORM 0 TOLERANCE HIGH PRECISION CUTTING for much better accuracy, if applicable. Clean and repack wheel bearings if equipped. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle. PLEASE GIVE BRAKES ABOUT 50 TO 100 MILES TO BREAK IN……..THANKS DAVE
    • WHEEL HUB – Remove & Replace – 3500,4WD Front,Assembly,w/Dual Rear Wheels,Both Sides – [DOES NOT include wheel alignment.]
     
    NICK J. gave our service a 5 star review on 8/16/2023

  • 2015 RAM 2500 HD

    RAM 2500 HD
    Mileage
    79,789
    Service Date
    8/2/2022
    Services Performed
    • CHECK COOLANT LEAK
    • WATER PUMP – Remove & Replace – V8,5.7L Eng
    • THERMOSTAT &/OR GASKET – Remove & Replace – V8
    • COOLANT – Drain & Refill
     
    MIKE K. gave our service a 5 star review on 8/12/2022

  • 2019 RAM 3500 HD

    RAM 3500 HD
    Mileage
    35,466
    Service Date
    11/29/2021
    Services Performed
    • FUEL FILTER – Remove & Replace – In-Line6 Chassis Mounted,Element
     
    CLAUDETTE H. gave our service a 5 star review on 12/3/2021

  • 2016 RAM 1500

    RAM 1500
    Mileage
    80,765
    Service Date
    10/8/2021
    Services Performed
    • You vehicle's diagnostic system has detected a problem that is causing it not to perform to factory standards, resulting in the control module turning on the check engine light (CEL). We are well equipped & trained to accurately diagnose & repair these problems. We can & will repair the car to factory standards, however, there may be more than one problem present. The engine management computer of your car is equipped with a sophisticated on-board diagnostic (OBD) system. When this system detects a problem it turns on the CEL. A problem in one of the monitored system is what turned on your CEL. Our technicians are highly trained & equipped with the latest state of the art diagnostic equipment, so that in most cases we will be able to diagnose & repair problems quickly and efficiently. There may be more than one problem present even though only one trouble code was recorded in the module. The module continually runs various self tests to ensure that all systems are working normally. In the event of a failure some of these self tests are turned off until the original problem is fixed. This means that until we repair the original problem we may not be able to see other problems. This is likely to occur if you have been driving with the CEL for multiple days.
    • WATER VALVE – Remove & Replace
     
    MATT H. gave our service a 5 star review on 10/13/2021