Call (661) 252-1400

Home 2021-03-15T18:11:29+00:00

Reeves Complete Auto Center is committed to providing you excellent service, so you always choose us for your repair needs.

For most people, auto maintenance and repair is not fun or convenient. So, we want to make the process as easy and enjoyable as possible for you. We genuinely care about your car and your experience, and it shows. Our first-time customers continually become our long term customers time and time again, choosing us for all their auto needs.

Affiliates &
Certifications

Recently Serviced Vehicles

2016 Mazda CX-5

Mazda CX-5

Mileage
93,398
Service Date
7/20/2021
Services Performed
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
 
EVAN S. gave our service a 5 star review on 7/20/2021

2017 Ford Mustang

Ford Mustang

Mileage
36,169
Service Date
6/28/2021
Services Performed
  • Diagnose engine overheating
  • WATER PUMP – Remove & Replace – 3.7L Eng
 
GREG S. gave our service a 5 star review on 6/28/2021

2005 Lincoln LS

Lincoln LS

Mileage
263,741
Service Date
6/17/2021
Services Performed
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
  • Diagnose air conditioning system
  • A/C COMPRESSOR – Remove & Replace – V6 – [DOES NOT include Air Conditioning System recover, evacuate and/or recharge.]
  • AIR COND HOSE – Remove & Replace – One – [NOTE: For Manifold and Tube Assembly, refer to Manifold & Tube Assembly – R&R DOES NOT include Air Conditioning System evacuate or charge system.]
  • SHIPPING CHARGES
  • CONDENSER – Remove & Replace – [DOES NOT include Air Conditioning System recover, evacuate and/or recharge.]
  • ACCUMULATOR OR RECEIVER DRIER – Remove & Replace – [DOES NOT include Air Conditioning System recover, evacuate and/or recharge.]
  • Service air conditioner. Check condition of all belts and lines. Evacuate and recharge with R-134. Test system performance. SPECS AFTER RECHARGE – LOW SIDE – (40)PSI HIGH SIDE – (170)PSI CENTER VENT TEMP – (44)DEGREES
 
WALTER M. gave our service a 5 star review on 6/18/2021

2011 Chevrolet Silverado

Chevrolet Silverado

Mileage
120,729
Service Date
6/11/2021
Services Performed
  • R/R AXLE SEAL & REAR BRAKES
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
  • WHEEL SEAL – Remove & Replace – 1500 w/Rear Disc Brakes,One Side – [Includes: Repack and adjust Bearings (where applicable).]
 
ALEX R. gave our service a 5 star review on 6/11/2021

2017 GMC Canyon

GMC Canyon

Mileage
103,504
Service Date
5/28/2021
Services Performed
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
 
JOHN F. gave our service a 5 star review on 5/29/2021

2008 Acura TL

Acura TL

Mileage
158,733
Service Date
4/30/2021
Services Performed
  • CHECK SQUEAKING NOISE LIKE STRUTS OR SHOCKS
  • CONTROL ARM – Remove & Replace – Both,Lower – [DOES NOT include alignment.]
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
  • STRUT ASSEMBLY – Removal & Installation – Both – [DOES NOT include alignment.]
  • 4 WHEEL ALIGNMENT
 
SHIELA D. gave our service a 5 star review on 5/8/2021

2014 Ford F-150

Ford F-150

Mileage
74,079
Service Date
4/30/2021
Services Performed
  • CHECK OIL PRESSURE KEEPS FLUCTUATING ????
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
  • REMOVE & REPLACE DEFECTIVE OIL PRESSURE SENDER & RECHECK`
 
JAMES S. gave our service a 5 star review on 5/8/2021

2016 Toyota Sequoia

Toyota Sequoia

Mileage
75,260
Service Date
4/12/2021
Services Performed
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
 
GLENDA G. gave our service a 5 star review on 4/14/2021

2011 Chevrolet HHR

Chevrolet HHR

Mileage
69,343
Service Date
4/6/2021
Services Performed
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
  • WHEEL HUB – Remove & Replace – Front,Both
  • You car's diagnostic system has detected a problem that is causing it not to perform to the standards set by the factory, and as a result the control module has turned on the check engine light. We are well equipped and trained to accurately diagnose and repair these problems. We can and will repair the car to factory standards,however, there may be more than one problem present. The engine management computer of your car is equipped with a sophisticated on-board diagnostic (OBD) system. When this system detects a problem it turns on the check engine light (CEL), sometimes called a multifunction indicator light (MIL). A problem in one of the monitored system is what turned on your CEL. Our technicians are highly trained and equipped with the latest state of the art diagnostic equipment, so that in most cases we will be able to diagnose and repair problems quickly and efficiently. There may be more than Problem Present even though Only one Trouble Code was Recorded in the Computer. The Computer Continually runs Various self Tests to ensure that All Systems are Working Normally. In the Event of a Failure some of these Self tests are Turned off Until the Original Problem is Fixed. This Means that until we Repair the Original Problem we may Not be Able to see Another Problem. This is More Likely to Occur if you have Been Driving for More Than Just a Few Days with The Mil Lite on.
 
LEON R. gave our service a 5 star review on 4/8/2021

2007 Nissan Xterra

Nissan Xterra

Mileage
113,169
Service Date
4/2/2021
Services Performed
  • You car's diagnostic system has detected a problem that is causing it not to perform to the standards set by the factory, and as a result the control module has turned on the check engine light. We are well equipped and trained to accurately diagnose and repair these problems. We can and will repair the car to factory standards,however, there may be more than one problem present. The engine management computer of your car is equipped with a sophisticated on-board diagnostic (OBD) system. When this system detects a problem it turns on the check engine light (CEL), sometimes called a multifunction indicator light (MIL). A problem in one of the monitored system is what turned on your CEL. Our technicians are highly trained and equipped with the latest state of the art diagnostic equipment, so that in most cases we will be able to diagnose and repair problems quickly and efficiently. There may be more than Problem Present even though Only one Trouble Code was Recorded in the Computer. The Computer Continually runs Various self Tests to ensure that All Systems are Working Normally. In the Event of a Failure some of these Self tests are Turned off Until the Original Problem is Fixed. This Means that until we Repair the Original Problem we may Not be Able to see Another Problem. This is More Likely to Occur if you have Been Driving for More Than Just a Few Days with The Mil Lite on.
 
JOHN S. gave our service a 5 star review on 4/8/2021

2012 Nissan Frontier

Nissan Frontier

Mileage
190,317
Service Date
3/31/2021
Services Performed
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
  • EVAPORATION CONTROL CANISTER – Remove & Replace
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
  • You car's diagnostic system has detected a problem that is causing it not to perform to the standards set by the factory, and as a result the control module has turned on the check engine light. We are well equipped and trained to accurately diagnose and repair these problems. We can and will repair the car to factory standards,however, there may be more than one problem present. The engine management computer of your car is equipped with a sophisticated on-board diagnostic (OBD) system. When this system detects a problem it turns on the check engine light (CEL), sometimes called a multifunction indicator light (MIL). A problem in one of the monitored system is what turned on your CEL. Our technicians are highly trained and equipped with the latest state of the art diagnostic equipment, so that in most cases we will be able to diagnose and repair problems quickly and efficiently. There may be more than Problem Present even though Only one Trouble Code was Recorded in the Computer. The Computer Continually runs Various self Tests to ensure that All Systems are Working Normally. In the Event of a Failure some of these Self tests are Turned off Until the Original Problem is Fixed. This Means that until we Repair the Original Problem we may Not be Able to see Another Problem. This is More Likely to Occur if you have Been Driving for More Than Just a Few Days with The Mil Lite on.
 
LORN H. gave our service a 5 star review on 4/1/2021

2007 Lexus RX 400h

Lexus RX 400h

Mileage
228,312
Service Date
3/18/2021
Services Performed
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
 
AMIR S. gave our service a 5 star review on 3/31/2021

2015 Acura RDX

Acura RDX

Mileage
108,899
Service Date
3/17/2021
Services Performed
  • (Combination) – CRANKSHAFT GEAR OR SPROCKET – Remove & Replace
  • (Combination) – TIMING BELT IDLER PULLEY – Remove & Replace
  • (Combination) – TIMING BELT TENSIONER – Remove & Replace
  • (Combination) – WATER PUMP – Remove & Replace
  • CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
  • DRAIN & FILL TRANS & REAR DIFF FLUIDS
  • TIMING BELT – Remove & Replace
  • TRANSAXLE OIL – Remove & Replace – In Line
  • VARIABLE VALVE TIMING OIL PRESSURE SWITCH – Remove & Replace
  • You car's diagnostic system has detected a problem that is causing it not to perform to the standards set by the factory, and as a result the control module has turned on the check engine light. We are well equipped and trained to accurately diagnose and repair these problems. We can and will repair the car to factory standards,however, there may be more than one problem present. The engine management computer of your car is equipped with a sophisticated on-board diagnostic (OBD) system. When this system detects a problem it turns on the check engine light (CEL), sometimes called a multifunction indicator light (MIL). A problem in one of the monitored system is what turned on your CEL. Our technicians are highly trained and equipped with the latest state of the art diagnostic equipment, so that in most cases we will be able to diagnose and repair problems quickly and efficiently. There may be more than Problem Present even though Only one Trouble Code was Recorded in the Computer. The Computer Continually runs Various self Tests to ensure that All Systems are Working Normally. In the Event of a Failure some of these Self tests are Turned off Until the Original Problem is Fixed. This Means that until we Repair the Original Problem we may Not be Able to see Another Problem. This is More Likely to Occur if you have Been Driving for More Than Just a Few Days with The Mil Lite on.
 
CHRIS M. gave our service a 5 star review on 3/17/2021

2007 Hyundai Santa Fe

Hyundai Santa Fe

Mileage
132,954
Service Date
3/11/2021
Services Performed
  • PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
  • Remove All four wheels to inspect brake condition. Inspect entire system for leaks. Lining remaining is: Front (%) Rear (%)
 
JOHN R. gave our service a 5 star review on 3/11/2021

2014 Jeep Grand Cherokee

Jeep Grand Cherokee

Mileage
106,964
Service Date
3/9/2021
Services Performed
  • CHECK ON ADJUSTING E BRAKE AND ZIP TIE ECU CONNECTOR
  • CLEAN & ADJUST REAR BRAKES AS NEEDED
  • PASSENGER SIDE
  • TRANSMISSION OIL PAN GASKET &/OR FILTER – Remove & Replace – V6,3.6L Eng – [Includes: Additional time for use of scan tool to perform this procedure.]
  • Unplug and Cut Off the Old Connector, Strip the End, Then Cut the end of the wire cleanly, and then place the wire with 3/4 inch of it sticking out of the stripper. Then pull the wire out, removing 1/4 inch of the insulator. Twist the end of the wire. Next crimp the New Connector, Insert the stripped end of the wire into the connector until it bottoms out. Then, place the connector about 1/8 of an inch from the wire end of the connector into the crimp and crimp together. Plug the fixed connector back in
 
JOHN H. gave our service a 5 star review on 3/11/2021

2015 Toyota Sienna

Toyota Sienna

Mileage
64,991
Service Date
3/5/2021
Services Performed
  • Remove All four wheels to inspect brake condition. Inspect entire system for leaks. Lining remaining is: Front (%) Rear (%)
  • Replace front brake pad linings and machine front brake disc rotors on vehicle with new state of the art on car brake lathe, THAT WILL PERFORM 0 TOLERANCE HIGH PRECISION CUTTING for much better accuracy. Clean and repack wheel bearings if equipped. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle. PLEASE GIVE BRAKES ABOUT 50 TO 100 MILES TO BREAK IN……..THANKS DAVE
  • SHIMMY IN BRAKE PEDAL
 
MERVIL T. gave our service a 5 star review on 3/6/2021