Confirmed dealership's diagnosis of faulty fuel pump, have power and ground going to pump, manually applied power to fuel pump and no operation, rec fuel pump
FUEL PUMP – Remove & Replace – V6,3.6L Eng w/o Skid Plate/Trailer Tow Equipped,Left,Main – [Includes: R&I Fuel Tank.]
JAMES E. gave our service a 5 star review on 6/8/2023
2015 Jeep Grand Cherokee CRM Mitchell1
2023-06-10T22:01:43+00:00
AIR COND HOSE – Remove & Replace – 2.4L Eng Discharge Line – [Includes: R&I Front Bumper Cover.] – [DOES NOT include Air Conditioning System recover, evacuate and/or recharge.]
Service air conditioner. Check condition of all belts and lines. Evacuate and recharge with R-1234YF. Test system performance. SPECS AFTER RECHARGE – LOW SIDE – (30)PSI HIGH SIDE – (200)PSI CENTER VENT TEMP – (42)DEGREES
KATHY P. gave our service a 5 star review on 5/24/2023
CHECK VEHICLE COMPLETELY & REPORT FINDINGS ON ATTACHED SHEET.
PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
CONTROL ARM – Remove & Replace – Front, Upper, Both Sides – [DOES NOT include alignment.]
CONTROL ARM – Remove & Replace – Lower, Both Sides – [DOES NOT include alignment.]
2 WHEEL ALIGNMENT
AIR FILTER – Remove & Replace – All Models
RUTH R. gave our service a 5 star review on 4/20/2022
2008 Jeep Grand Cherokee CRM Mitchell1
2022-04-21T21:59:41+00:00
PERFORM OIL CHANGE, INSTALL NEW OIL FILTER, DRAIN PLUG GASKET AND FILL OIL TO SPEC. CHECK AND TOP OFF ALL FLUIDS. CHECK AND ADJUST TIRE PRESSURE TO SPEC PERFORM PREVENTATIVE MAINTENANCE INSPECTION RESET MAINTENANCE LIGHT IF ITS ON OR OFF INSTALL OIL CHANGE STICKER TO WINDSHIELD
RONALD D. gave our service a 5 star review on 2/4/2022
CHECK FOR POSSIBLE WATER PUMP LEAK, CHECK FOR POSSIBLE RADIATOR LEAK, ALSO CHECK FOR OVERHEATING ISSUE
CHECK OIL LEAK
CYLINDER HEAD GASKET – Remove & Replace – Both Sides – [Includes: Remove carbon and check surfaces for warpage. Includes adjust Valves (where applicable) and clean and adjust Spark Plugs.]
REBUILD CUSTOMER CYLINDER HEADS TO FACTORY SPECIFICATIONS WITH UPGRADED HARDENED EXHAUST SEATS
PROPELLER SHAFT – Removal & Installation – Front
RONALD D. gave our service a 5 star review on 12/14/2021
CHECK ON ADJUSTING E BRAKE AND ZIP TIE ECU CONNECTOR
CLEAN & ADJUST REAR BRAKES AS NEEDED
PASSENGER SIDE
TRANSMISSION OIL PAN GASKET &/OR FILTER – Remove & Replace – V6,3.6L Eng – [Includes: Additional time for use of scan tool to perform this procedure.]
Unplug and Cut Off the Old Connector, Strip the End, Then Cut the end of the wire cleanly, and then place the wire with 3/4 inch of it sticking out of the stripper. Then pull the wire out, removing 1/4 inch of the insulator. Twist the end of the wire. Next crimp the New Connector, Insert the stripped end of the wire into the connector until it bottoms out. Then, place the connector about 1/8 of an inch from the wire end of the connector into the crimp and crimp together. Plug the fixed connector back in
JOHN H. gave our service a 5 star review on 3/11/2021
2014 Jeep Grand Cherokee CRM Mitchell1
2021-03-12T23:03:30+00:00